KitchenAidRepair Miami

Starting figures and researched market ranges — never a quote

How much does it cost to repair a KitchenAid in Miami? It depends, and here is on what.

Below is what each repair starts at in South Florida, the market range it was set against, and an honest account of what pushes a particular job up or down. Both are starting points rather than a price for your appliance. Nothing on this site is a final figure: the exact cost is settled at the appliance, after the diagnostic, and written down before anything is opened.

  • 19 repairs with a published figure
  • from $95 diagnostic, credited to the repair
  • $0 for anything you can do yourself
  • In writing the scope and the price, before anything is opened

Book a visit

Book a diagnostic visit

Your model number and a line about what it is doing is enough to get started. We will confirm the earliest slot we can genuinely keep.

  • Diagnostic from $95, credited toward the repair when you go ahead
  • The work and the price in writing before anything is opened
  • A warranty on our workmanship
  • Miami-Dade, Broward and Palm Beach counties
  1. 01 You tell us the model and what the unit is doing. A photo of the display helps.
  2. 02 We come back with the earliest slot we can genuinely keep, not the earliest one that sounds good.
  3. 03 Diagnosis on site, then the scope and the price in writing before anything is opened.

Your details stay private. No spam, ever.

Loading the booking form…

The booking form is taking longer than it should. Call (305) 306-1328 and we will book the visit with you.

By job

Every figure, and what moves it

Each page carries the starting figure, the researched market range it was checked against, and the three things that decide where inside that range your repair actually lands.

  • Diagnostic visit cost

    What the first visit costs, why it is the only honest way to price a repair, and why it comes off the bill. This is the company rate rather than anything to do with the badge — a dishwasher and a wall oven cost the same to diagnose.

    • Researched market range for South Florida: service calls $59–$129
    • Credited toward the repair when you go ahead
    • A second appliance on the same visit costs less than a second visit
    What moves this figure
  • Range hood and venting repair cost

    The cheapest band on this site, and we would rather say so than pad it. Everything that moves air out of your kitchen is priced here — canopy hoods, insert liners, the vent side of a microwave-hood combination, and the downdraft that rises out of the counter.

    • Researched market range: hood repair $100–$400; capacitor $120–$250; blower motor $250–$550
    • A hum with no rotation is usually a capacitor, at the bottom of the band
    • The downdraft is the top: mechanical before it is electrical
    What moves this figure
  • Dryer repair cost

    A legacy machine and the cheapest laundry work on this site, for a good reason: every KitchenAid dryer still running here is vented, which makes it the simplest appliance we are called to. Heat, airflow, drum, belt and rollers, priced together.

    • Researched market range: dryer repair $100–$300; element $150–$350
    • The floor is a vent cleaning — and it is often the whole answer
    • Parts availability is checked before anything is ordered
    What moves this figure
  • Dishwasher not cleaning: repair cost

    Spotting, film, and dishes that come out no cleaner than they went in. In this water most of these calls are the wash side rather than a motor — which is why this is the cheapest dishwasher figure on the site and why it starts with the filter.

    • Researched market range: cleaning and descaling service $120–$250
    • Circulation motor $250–$550 and diverter $200–$400 are the top of the band
    • Which rack is failing identifies the diverter before anybody arrives
    What moves this figure
  • Ice and water system repair cost

    The most-serviced thing on a French-door refrigerator, and the reason is the design rather than the badge. One inlet valve and one filter feed both the ice maker and the dispenser, which is why they are priced on one page.

    • Researched market range: inlet valve $175–$350; ice maker assembly $200–$400
    • The floor is an undercounter machine cleaning and descale
    • A freeze plug in the fill tube costs the visit and nothing else
    What moves this figure
  • Refrigerator door and gasket repair cost

    The cheapest job on the refrigeration list, and the one that imitates the most expensive one. A tired seal produces a cabinet that will not hold temperature and a compressor that never stops — every symptom of a repair four times the price.

    • Researched market range: hinge, adjustment and alignment $150–$350
    • The dollar-bill test is free and takes a minute
    • Gaskets are ordered to the model, not cut from a strip
    What moves this figure
  • Refrigerator not cooling: repair cost

    Where most refrigeration calls actually land, and the band you reach the expensive one by eliminating. Airflow, defrost, dampers and sensors — everything between "it is not cold" and the sealed system.

    • Researched market range: evaporator fan $200–$400; defrost heater $200–$450
    • A warm fresh-food side with a cold freezer is airflow, not refrigerant
    • Sensors and thermistors are $100–$250 and are the cheap answer
    What moves this figure
  • Appliance maintenance cost

    One visit, every appliance in the house. This is the widest line on the fleet, so a kitchen furnished throughout with it can be eight or ten machines — and doing them on one trip is meaningfully cheaper than doing three on two.

    • Researched market range: multi-appliance service $120–$300
    • The second and third appliance are far cheaper than the first
    • Filters, condensers, ducts, seals and descaling in one appointment
    What moves this figure
  • Dishwasher not draining: repair cost

    Water standing in the tub at the end of a cycle. Four things usually cause it and three of them are outside the appliance, which is why this page starts at the sink and why a real share of these calls end at the visit fee.

    • Researched market range: drain pump $200–$400
    • Three of the four usual causes are not the appliance
    • A leak from underneath is looked at the same day
    What moves this figure
  • Microwave repair cost

    The light is on, the turntable turns, and nothing gets hot. That is the expensive version. The cheap version — a door switch or a control — is more common, which is why the figure starts there rather than at the magnetron.

    • Researched market range: microwave repair $100–$300
    • Door switches and controls are the commoner half by a distance
    • The high-voltage side is never an owner repair, ever
    What moves this figure
  • Gas burner and ignition repair cost

    A burner that clicks and will not light, or lights and will not stay. The starting figure is one igniter on one burner, and a real share of these calls turn out to be a cap seated wrong after a cleaning.

    • Researched market range: igniter $150–$400; burner service $100–$250
    • A cap or a cross-slot in the wrong place costs the visit only
    • Clicking that will not stop is usually moisture, not a part
    What moves this figure
  • Cooktop and induction repair cost

    One zone that has stopped, a surface that will not respond, or an induction top that keeps shutting itself off. Three very different jobs in one band, and the diagnosis decides which end of it you are at.

    • Researched market range: ceramic surface $300–$600 plus labor; induction module $300–$700
    • Most induction calls are protections tripping, and cost the visit
    • A cracked surface goes off at the breaker and stays off
    What moves this figure
  • Dishwasher control and door repair cost

    A machine that will not start, a panel that will not respond, a door that will not latch, and the rack adjuster that quietly broke. Two ends of one band, and the cheap end is much more common than the expensive one.

    • Researched market range: door seal $150–$320; hinge and spring $180–$380
    • A control board is $150–$300 and is confirmed before it is ordered
    • The upper rack adjuster is a known small job on 2010–2019 machines
    What moves this figure
  • Washing machine repair cost

    A legacy machine, and the row where "is it worth it" is a real question rather than a formality. Drain and pump work at the bottom, drive and bearing work at the top, and a parts check before anything is ordered.

    • Researched market range: drain pump $200–$420; bearing and drive $400–$900
    • Parts availability is confirmed before an order, not after
    • On some of these machines the honest answer is not to repair
    What moves this figure
  • Appliance installation cost

    Where a meaningful share of the repairs on this site are either prevented or created. A dishwasher that never drained from the day it went in was not a repair waiting to happen — it was an installation.

    • Researched market range: installation $150–$500; built-in $200–$600
    • Drain loops, knock-out plugs and duct runs are the whole argument
    • Leveled, sealed, run and proved before the visit ends
    What moves this figure
  • Oven repair cost

    An oven that will not heat, one that runs hot or cold, or one that stopped part-way through a self-clean and locked its own door. Heat, sensing, doors and latches, priced together because the self-clean cycle takes all four at once.

    • Researched market range: sensor $100–$250; element $150–$450; latch $200–$450
    • A thermal fuse blown after a self-clean will very likely go again
    • Access is the difference: a tall housing against a floor-level range
    What moves this figure
  • Wine cellar repair cost

    A small cabinet with an expensive job, in a climate working against it. When one of these drifts, what is inside it is usually worth a good deal more than the repair — which is the argument for looking sooner rather than later.

    • Researched market range: thermistor $150–$300; zone fan or damper $200–$400
    • One zone wrong rules out the compressor immediately
    • Air behind the cabinet is the commonest thing nobody checks
    What moves this figure
  • Oven and range control board repair cost

    A panel that will not respond, a display showing a code that will not clear, or an appliance that came back from a power outage confused. The most expensive cooking repair short of the appliance itself, and the one most often diagnosed wrongly.

    • Researched market range: control board $150–$300 on mainstream equipment
    • Current platforms carry more than one board and a network between them
    • The board is never ordered on the strength of a code alone
    What moves this figure
  • Sealed system and compressor repair cost

    The largest figure on this site, and the only one that is quoted last. It is reached by measuring and excluding everything cheaper, and on an older cabinet the honest answer is sometimes that it is not worth doing.

    • Researched market range: compressor $600–$1,200; leak repair $400–$900
    • Quoted only after the cheaper causes are excluded on record
    • Recovered, repaired, evacuated and charged by weight to the plate
    What moves this figure

Why nobody can name your figure over the phone

One symptom, four ordinary causes, hundreds of dollars between them.

Take the commonest call on this site: a refrigerator that is not cold. That is a tired door seal at from $155, or airflow — a fan, a damper, a defrost circuit — at from $155, or a control and sensor problem at from $225, or the sealed system at from $650. Four causes, all ordinary, all common, all producing the identical complaint in your kitchen. The most expensive one is more than four times the cheapest.

Nothing you can tell us on the phone separates them, and nothing the appliance shows on its display separates them either — a code narrows the search, it does not end it. Only measurement at the appliance does. So we quote the cheapest cause we can honestly exclude, in order, and you get the list of what was measured rather than a conclusion. If somebody names your figure before seeing the machine, they have either padded it to cover the worst case or they will revise it when the panel comes off.

See what each repair involves
Two people standing at a kitchen island in conversation, one gesturing toward something out of frame, both seen from the shoulders down so no faces are visible.

How to read a figure on this site

What is in it, what moves it, what is never in it

The same three rules apply to every page in this archive, and to every number on the rest of the site.

In the figure

  • Parts and labor together, unless the page says otherwise
  • Getting the appliance out of its opening where the job needs that
  • A written scope and price, agreed before anything is opened
  • Our warranty on the work we performed and the parts we fitted

What moves it

  • Access — integrated behind your own panel, in a tall housing, or stacked
  • Which part it turns out to be: a sensor and the circuit it watches share one complaint
  • Whether the part is current, or has to be sourced for an appliance no longer built
  • How many appliances we see on one visit

Never in it

  • A price named before the appliance has been looked at
  • Anything the maker asks the owner to check — you get told instead
  • A brand premium. Where a job costs what it costs on any make, it is published at that
  • A figure for the high-voltage side of a microwave, which is quoted only after a diagnostic

The three cheapest rows here are the most valuable ones

Some of these figures exist to keep the others away.

A dryer vent cleaning at from $135. Hood filters and a duct at from $125. A maintenance visit at from $165 that clears refrigeration condensers along with everything else. Between them they are the cheapest items in this archive.

What they prevent is a hood blower motor, a dryer element and a repeat thermal fuse, and the sealed system repair at from $650 that is the largest figure we publish. You do not have to take that on trust: every one of those figures is on its own page here with the researched market range it was set against, so the arithmetic is yours to check. In this heat and this humidity it really is arithmetic rather than advice.

Appliance maintenance
A soft brush and a slim vacuum crevice tool lying on a pale tile kitchen floor next to a cabinet kickplate, a forearm in a dark work shirt reaching in from the edge of frame.

By appliance

Or start from the machine instead

If you are not sure which job yours is, the appliance page describes what tends to go wrong on it and points at the figure for each one.

  • An integrated dishwasher standing open behind a light wood panel, both racks out, a cutlery basket in the lower one, the control strip along the top edge of the door
    Integrated control · Front control · Third rack · ProDry · 24" · 39–44 dBA

    Dishwashers

    The appliance this name means in a kitchen, and the one that tells you the most before anybody arrives. A KitchenAid dishwasher with no display still reports its code — it flashes it on the Clean light, in two bursts, and those two numbers are a diagnosis you can read from across the room before anybody opens anything.

    Dishwasher repair
  • A tall stainless French door refrigerator filling the frame, both upper doors closed and the freezer drawer below shut, standing between cabinets in a bright kitchen, shot straight on from a few steps away.
    French door · Side-by-side · Bottom mount · Built-in · Counter-depth · 30"–48"

    Refrigerators

    The largest part of this maker's line and the largest part of our phone. French door and side-by-side, freestanding and built into cabinetry, counter-depth and full depth — and one code that South Florida sees more than anywhere else, because it is the one a cabinet shows after the power has been off.

    Refrigerator repair
  • A freezer compartment with its drawers pulled out, clear boxes of frozen food stacked in them
    Freezer drawers · Bottom mount · Side-by-side · Ice build-up · Frost

    Freezers

    This make does not sell a standalone freezer, and that is worth saying plainly: the freezer here is the bottom drawer of a French-door cabinet, one column of a side-by-side, or a refrigerated drawer set to freeze. It is still the half people call about, because a freezer that stops is a freezer full of food.

    Freezer repair
  • An ice bin filled to the top with clear cubes, seen straight down
    Undercounter 15" and 18" · 25 lb and 35 lb · Clear Ice · Panel-ready · In-door

    Ice makers

    Two different appliances share this card, and knowing which one you have changes everything. There is the ice maker inside the refrigerator, and there is the undercounter machine that does nothing else — a real ice maker with its own drain, its own water line and its own cleaning cycle. In this climate the second one earns its keep and asks for attention.

    Ice maker repair
  • An undercounter wine cabinet built into dark cabinetry, bottles lying on wooden shelves behind a glass door, lit warm inside
    Undercounter 15" and 24" · Wine cellars · Beverage centers · Panel-ready · Glass door

    Wine cellars and beverage centers

    Small cabinets with an expensive job. A wine cellar holds a narrow band of temperature behind a glass door, in a climate that is working against it and often in a cabinet with very little air. When one drifts, what is inside it is usually worth more than the repair.

    Wine cellar repair
  • A stainless slide-in range set between white shaker cabinets under a hood, a dishwasher at the right, bright daylight
    Commercial-Style · Slide-in · Freestanding · Double oven · Downdraft · Gas, electric, dual fuel, induction

    Ranges

    One appliance and two systems that fail independently. More than half of this maker's current ranges are the Commercial-Style machines — heavy, knob-controlled, gas or dual fuel or induction — and the rest are slide-ins and freestanding ranges, including a downdraft model with the ventilation built into the appliance itself.

    Range repair
  • A stainless gas cooktop seen close from one side, four sealed burners with cast grates and a row of knobs along the front edge
    Gas · Gas-on-glass · Electric radiant · Induction · Downdraft · 15", 30", 36"

    Cooktops

    Four different appliances under one word. Gas with sealed burners, gas on a glass surface, electric radiant under ceramic, and induction — plus the downdraft versions of two of them, with a blower built into the counter. What has gone wrong is usually obvious once you know which one you are standing in front of.

    Cooktop repair
  • A built-in oven with the door open and a tart baking on the shelf, the cavity lit warm, knobs and a touch control panel above the door
    Single · Double · Combination microwave-oven · 24", 27", 30" · True Convection · Self-clean

    Wall ovens

    Built into a tall housing, surrounded by cabinetry, and heavy. A wall oven is the appliance where the access is a real part of the job — and the combination units, with a microwave above the oven, are two appliances in one opening that report separately and fail separately.

    Wall oven repair
  • A black built-in microwave set into a run of dark cabinetry above a cooktop, its door closed
    Over-the-range · Built-in · Low profile · Microwave-hood combination · Countertop · Air Fry

    Microwaves

    The appliance nobody thinks about until the light is on and nothing is hot. Over-the-range, built into a cabinet with a trim kit, or the microwave-hood combination that also ventilates your cooktop — and on that last one, a dead microwave means a dead hood as well.

    Microwave repair
  • A stainless chimney hood mounted on a tiled wall above a gas cooktop in a white kitchen
    Wall-mount · Under-cabinet · Island · Commercial-Style · Custom liners · Retractable downdraft

    Range hoods and vents

    The appliance that gets attention only when it is silent, and the one whose maintenance is genuinely all an owner needs to do. Wall-mounted canopies, under-cabinet hoods, island hoods, insert liners for custom millwork, and the retractable downdraft that rises out of the counter.

    Range hood repair
  • A front-loading washing machine standing in a domestic laundry room with its door open on the empty stainless drum, a folded towel on the machine beside it and a basket on the floor, no person in the frame.
    Superba · Ensemble front-load · Top-load · No longer manufactured · Still repaired

    Washing machines

    Worth saying in the first line: KitchenAid does not sell washing machines in the United States any more. There is no laundry section in its own catalog and no laundry family in its own support base. The machines are still in South Florida homes and garages, people still search for them by name, and we still repair them — this page is about a machine that is no longer made.

    Washing machine repair
  • The inside of a dryer drum seen through the open door, the perforated stainless wall and the lifting vanes
    Electric and gas · Vented · Ensemble front-load · No longer manufactured · Still repaired

    Dryers

    The same situation as the washer next to it, and usually the same laundry room. KitchenAid stopped selling dryers in the United States, and the ones still working here are vented electric and gas machines that people search for by model number to this day. A vented dryer is a simple appliance, which is why so many of these calls end well.

    Dryer repair

Want a number before we come out?

19 published figures is not the limit of what we quote.

A job gets a page here when its figure is genuinely its own. Plenty of work sits inside another page’s band — a lamp, a switch, a hinge, a hose — and is quoted the same way without needing a page of its own. And there are repairs nobody has typed into a search box that we do every week.

What we can do on the phone is narrow it. With the model number and a description of what the appliance is doing, we will tell you which of these figures your job is likely to sit near and what would push it to the other end. That costs nothing and commits you to nothing. Call (305) 306-1328, or use the form and describe it in your own words.

About the money

The questions people ask about price

How much does it cost to repair a KitchenAid refrigerator?

It depends entirely on which repair it is, and the spread is wide enough that an average would mislead you. A door seal or a blocked defrost drain starts at $155. Airflow and defrost work runs from there to about $245. A control or sensor repair starts at $225. Sealed system and compressor work starts at $650. Those are starting figures and researched market ranges for South Florida, not a price for your cabinet — the exact cost is confirmed after an on-site diagnostic and agreed before anything is opened.

Why will you not give me a firm price over the phone?

Because the same symptom has several ordinary causes that sit hundreds of dollars apart, and only the appliance settles which one is yours. A firm number before the diagnostic would either be padded to cover the worst case or too low to honor when the panel comes off. We would rather give you the range, then confirm the figure once we have measured.

Where do these numbers come from?

They are researched market ranges for South Florida — national cost bands for the same parts and the same labor, narrowed by what the part actually is on this equipment and by what the installation does to the time. They are researched figures rather than a record of our own invoices, and this site says so plainly rather than implying otherwise.

Is the diagnostic fee extra?

It is charged for the visit and credited toward the repair when you go ahead, so on a job we carry out it is not added on top of the figures here. If you decide not to proceed, it is the only thing you pay.

Do you charge more because it is a KitchenAid?

No. Where a job costs what it costs on any make — a hood capacitor, an oven sensor, a dryer belt — it is published at that figure. The rows that are genuinely higher are higher because of the machine or the installation, and each page says which.

What about the washer and dryer?

Those two are honest special cases. This maker no longer sells washers or dryers in the United States, and the machines still running here are from the second half of the 2000s or earlier. We repair them, and the figures are on this page — what they add is a parts check before anything is ordered, because mechanical and electrical parts are commonly still available while consoles, panels and trim frequently are not.

When is a repair not worth doing?

When the work approaches what the appliance is worth, or when a second major failure is already visible. That is a conversation we have on the visit, before the part is ordered, rather than a line you read on an invoice afterwards. It happens most on the sealed system row and on laundry drive work.

In more detail

How repair pricing works here, and why we publish ranges

A starting point is not a quote

Every figure on this site is where a repair of that kind starts in South Florida, together with the researched market range the same work is quoted in. Neither is a price for your appliance and neither is presented as one. The exact cost is settled after an on-site diagnostic and agreed with you in writing before anything is opened.

Where the numbers come from, said plainly

They are researched market ranges for South Florida rather than a record of this company’s own invoices. National cost bands for the same parts and the same labor, narrowed by what the part actually is on this equipment and by what the installation does to the time. We would rather tell you that than imply a billing history behind a number, and when real job figures replace them these pages change and say so.

What actually moves a figure

  • The part. A thermal fuse and a control board are two orders of magnitude apart, and both present as an appliance that does nothing.
  • The access. A freestanding range rolls out. A wall oven comes out of a tall cabinet opening, a built-in refrigerator is trimmed into millwork, a fully integrated dishwasher carries your own cabinet panel, and a stacked laundry pair has to come apart before either half is reachable.
  • Whether the part is still made. On the current line most things arrive quickly. On the washers and dryers this maker no longer builds, mechanical and electrical parts are commonly still available while cosmetic parts and consoles frequently are not — and you are told which side of that line your repair sits on before anything is ordered.
  • What we find. The cheap cause is measured before the expensive one, and sometimes one failure has taken a second component with it.

Two things about KitchenAid equipment in South Florida

Hard water is the local subject, and the maker addresses it directly. Miami-Dade and Broward both soften their water at the treatment plant, because the groundwater they draw on is hard. KitchenAid recommends a water softener at 15 grains or more and publishes its own remedies for spotting and film. We will not print a hardness number for South Florida — no utility here publishes one and the figures sold online contradict each other by five times — so check your own utility’s report. What follows for the money is on the dishwasher and ice pages: descaling and filter service are cheap, and they keep the motors and the modules away.

Humidity is often not a problem at all. A French-door cabinet sweating down the middle in August is documented as normal in humid weather, and the first thing to try is turning Energy Saver off. That is a free answer, and it is on this site because a page that only sold repairs would have left it out.

Independent, and what that means for your bill

We are an independent repair company. We are not affiliated with, authorized by, or endorsed by any manufacturer, and we do not carry out repairs on any manufacturer’s behalf. What we do carry is our own warranty on the work we performed and the parts we fitted, and OEM parts are available on order. Brand names and model numbers on this site are the property of their respective owners and are used for identification only.

Get the range now, and the figure after the diagnostic.

Tell us the model number and what the appliance is doing. You will have the scope and the price in writing before anything is opened, and the diagnostic comes off the bill when you go ahead.

This article is based on:

  • Official manufacturer documentation
  • Internal repair procedures
  • Technician repair history
  • Company quality standards
Call (305) 306-1328