--- title: "The Clean light is blinking" description: "KitchenAid the Clean light is blinking: the most searched complaint on this whole make, and the one most people throw away by canceling it." url: "https://kitchenaidmiami.support/symptoms/dishwasher-clean-light-blinking/" date_modified: "2026-08-23" Appliance type: "Dishwashers" --- # KitchenAid the Clean light is blinking ### The fastest diagnosis is the code Count the flashes before you touch anything. They come in two bursts: the first burst is the F number, then a short pause, then the second burst is the E number, then a long pause and the whole thing repeats. Seven flashes, pause, one flash is F7 E1. Write both numbers down — canceling the cycle clears the code, and then the machine has told you nothing. ### Two bursts, two numbers KitchenAid uses **F#E#** codes — a function number and an error number. A dishwasher with no display flashes them on the Clean light instead of printing them: the first burst is the F, a short pause, the second burst is the E, then a long pause and it repeats until you stop it. Eight flashes, pause, four flashes is F8E4. Seven, pause, one is F7 E1. Once you have both numbers you are no longer describing a blinking light — you are naming a subsystem. ### Why canceling is the expensive move Cancelling clears the code, and a cleared code takes the free part of the diagnosis with it. The machine will usually report again on the next cycle, but not always the same way, and a technician who arrives to a blank panel starts from zero. Sixty seconds of counting is worth more than anything else you can do on this appliance. ### These codes are not exclusive to this badge Whirlpool, Maytag and KitchenAid share the same control platforms, and the same code means the same thing across all three. That is worth knowing when you are searching: a page about an F8E4 on another badge in the same group is describing your machine too. What it will not know is your model, and that is where we start. A water level or float problem The machine has decided it has too much water in it and has stopped filling. F8E4 is the code this appears as, and an obstructed float assembly is the usual reason. Water not arriving as expected A fill that takes too long reads to the control as a supply problem. The valve under the sink, the inlet valve and its screen, and the pressure in the line. Water not leaving The tub filter, the air gap, the disposal plug or the pump. A drain the machine cannot finish stops the cycle and lights the code. The heater circuit or its sensor A cycle that never reaches temperature reports itself rather than simply running long, which is why some blinking machines have nothing visibly wrong with them. The control board or the panel The last one on the list rather than the first, and where a machine ends up when the supply, the drain and the heat have all been proved good. Count both bursts and write them down Flashes, pause, flashes, long pause. The first number is F, the second is E. Do this before you press anything, because the code is the whole diagnosis and it does not survive a cancel. Then try one full power cycle Off at the breaker for a full minute, then back on. A control caught mid-write during a brownout clears this way surprisingly often here, and if the code comes straight back, that is real information too. Lift out the tub filter and rinse it It is in the floor of the tub under the lower rack: a quarter turn on the cylinder, then the flat screen underneath lifts out. Free, takes two minutes, and it is behind a large share of these. Then book the visit Tell us both numbers and the model number from the sticker on the edge of the door. With those two things we usually know what is coming before anybody drives anywhere. That blinking is a code What it usually means Clean blinking a set number of times, over and over Blinking and beeping together It blinks, and the cycle will not start The fastest diagnosis is the code Count the flashes before you touch anything. They come in two bursts: the first burst is the F number, then a short pause, then the second burst is the E number, then a long pause and the whole thing repeats. Seven flashes, pause, one flash is F7 E1. Write both numbers down — canceling the cycle clears the code, and then the machine has told you nothing. Two bursts, two numbers KitchenAid uses F#E# codes — a function number and an error number. A dishwasher with no display flashes them on the Clean light instead of printing them: the first burst is the F, a short pause, the second burst is the E, then a long pause and it repeats until you stop it. Eight flashes, pause, four flashes is F8E4. Seven, pause, one is F7 E1. Once you have both numbers you are no longer describing a blinking light — you are naming a subsystem. Why canceling is the expensive move Cancelling clears the code, and a cleared code takes the free part of the diagnosis with it. The machine will usually report again on the next cycle, but not always the same way, and a technician who arrives to a blank panel starts from zero. Sixty seconds of counting is worth more than anything else you can do on this appliance. These codes are not exclusive to this badge Whirlpool, Maytag and KitchenAid share the same control platforms, and the same code means the same thing across all three. That is worth knowing when you are searching: a page about an F8E4 on another badge in the same group is describing your machine too. What it will not know is your model, and that is where we start. ### Is the blinking the same as an error code? Yes. On a machine with a numeric display you would read F8E4; on yours the same code arrives as eight flashes, a pause, then four. The manufacturer documents the reading procedure itself. The only difference is that yours needs somebody to count. ### I already canceled it. Have I lost the code? Usually, yes — and it is not a disaster. Run the machine again and watch it: if the condition is still there, the code comes back. This time count the two bursts before you touch anything. ### My machine has a colored light bar instead. What do those mean? Those are status lights rather than codes on the newer machines: blue while it is washing, red while it is drying, white when the cycle is complete, and blinking when the cycle has been paused. A paused cycle is not an error, and the door being opened is the usual reason for it. --- **[Read full article: The Clean light is blinking](https://kitchenaidmiami.support/symptoms/dishwasher-clean-light-blinking/)**