--- title: "How to Reset KitchenAid Dishwasher Controls — and What You Erase by Doing It" description: "How to reset KitchenAid dishwasher controls properly: write the blink code down first, then cancel and drain, check control lock, then the breaker." url: "https://kitchenaidmiami.support/blog/how-to-reset-a-kitchenaid-dishwasher/" date_modified: "2026-08-23" Category: "Troubleshooting" --- # How to Reset KitchenAid Dishwasher Controls — and What You Erase by Doing It ## How to reset KitchenAid dishwasher controls, in the right order The reset itself takes about thirty seconds and there is almost nothing to it. The reason this page is longer than thirty seconds is that **doing it first is the mistake**, and it is a mistake that costs people a diagnosis. When one of these machines stops, it says so with its lights. Most KitchenAid dishwashers have no numeric display — the panel is a row of cycle names and a set of indicators — so the machine reports by flashing the Clean light in a pattern. That pattern is an error code. It exists nowhere else. There is no log, no history screen, no way to recall it afterward. And every reset on this page erases it. We have arrived at plenty of kitchens where the answer had been on that light an hour earlier and the only thing left was somebody's recollection that "it was blinking a lot." So the order below starts with a pen. ## Step one: write down what the light was doing The pattern arrives in **two bursts**: a run of flashes, a short pause, another run of flashes, then a long pause before it all repeats. The first burst is the **F** number and the second is the **E** number. Seven flashes, pause, one flash is **F7 E1**. Count both. Do not count straight through the short pause — reading seven-then-one as "eight blinks" invents a code that does not exist and sends every search you run afterward somewhere wrong. While you are there, two more observations that cost nothing: - **Is there water standing in the tub**, and roughly how much?- **Where did it stop** — early, mid-wash, or during the drain? Stopped dry and early is a water-arriving problem. Stopped with the tub full is a water-leaving problem. That is half a diagnosis, for free, before anybody opens anything. ## Step two: check it is not simply locked Before you reset anything, rule out **Control Lock**, because a locked machine looks exactly like a broken one and this is the single most common reason a perfectly healthy dishwasher appears not to be. It is switched on by holding one pad for a few seconds — on most of these a number key or a dedicated Lock pad, and the panel marks it. Holding the same pad again for about three seconds switches it off. It gets turned on by a dishtowel, by a child, and by whoever last wiped the panel down. On an **integrated-control** machine, where the buttons live along the top edge of the door, you cannot see any of this without opening the door, which is why an integrated machine in Control Lock reads as completely dead from the kitchen. ## Step three: cancel and drain This is the first real reset, and it is the one that abandons the cycle. **Press and hold Cancel, or Cancel/Drain** — the pad is named differently across the generations — until the indicators change and you hear the pump run. Then **let the drain finish.** Opening the door partway through means several inches of water on the floor, and these machines hold more than people expect. For most reported conditions this is the whole reset. The machine drains, the lights clear, and it will accept a new cycle. ## Step four: the breaker, for five full minutes If the condition comes straight back, or the panel is unresponsive and not locked, restart the control itself. **Switch the dishwasher off at the breaker.** Not at the panel — most of these have no true off. If it is on a switched outlet under the sink you can use that instead. **Leave it off for five full minutes.** Thirty seconds is not enough. The control holds enough residual charge to keep its state briefly, and a quick flick often changes nothing at all, which is precisely why so many people report that resetting their dishwasher "does not do anything." Then restore power and run the shortest cycle with the machine empty. ## Reading the result, which is the whole point This is the part that makes the reset worth doing at all, because a reset is a **test** rather than a repair. **It clears and does not come back.** The control was interrupted mid-write and got stuck. In South Florida that is not rare — a summer brownout, or a momentary cut while the machine was running, will do it. A proper power cycle clears that completely and nothing further is needed. **It comes straight back.** The condition is real, and the reset has done its job by telling you so. Something the machine is genuinely reporting does not go anywhere when the power does. That distinction is worth more than the reset itself, and it is why the pattern goes on paper first. Without the numbers, all you know afterward is that it is still broken. ## What no reset on this machine will reach Three things survive every reset there is, and trying to clear them this way is where an afternoon goes. **A blocked filter.** It sits in the floor of the tub under the lower rack and comes out by hand — a quarter turn on the cylinder, then the flat screen underneath lifts out. Rinse it under a tap. A blocked filter shows up as gritty dishes long before it shows up as a code. **A drain path outside the machine.** The air gap on the counter, the disposal plug that was never knocked out when the dishwasher was installed, the drain hose loop under the sink. Three of the four most common drainage causes are not inside the appliance at all, and no reset touches any of them. **A door that will not latch.** The control cannot start a cycle it cannot confirm the door for, and that reads on the panel as a machine ignoring you. It is mechanical and it will still be there afterward. If you have written down the code, canceled, checked the lock, given it five minutes at the breaker, and it is still reporting — that is the point to call rather than to keep resetting. Bring the model number from the sticker on the door edge and both halves of the code, and the visit starts with a diagnosis instead of a guess. Independent KitchenAid service across Miami-Dade, Broward and Palm Beach. We are not affiliated with, authorized by or endorsed by any manufacturer. --- **[Read full article: How to Reset KitchenAid Dishwasher Controls — and What You Erase by Doing It](https://kitchenaidmiami.support/blog/how-to-reset-a-kitchenaid-dishwasher/)**